DOSFLASH ENTER THE NUMBER OF AN ATAPI DRIVER

Sorry man but your either going to need to soder a tiny connection together or get a prob which runs to your comp serial or usb port. We thank you very much with Blackened! If you have not heard a sound, you should skip the unlock and check your PC speaker. Andreas Daum , Feb 9, Andreas Daum , Feb 8, Follow this instruction at once, point 4 and 5, that is, install the firmware I send to you on PW.

Uploader: Nishakar
Date Added: 20 November 2014
File Size: 17.23 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 73561
Price: Free* [*Free Regsitration Required]

It’s all about DOS! I have a 1.

Liteon DG-16D2S Erase/Flash Support Here! DONT think its a brick read first.

Thanks, the Phoenix shall rise. HP would be preferred.

Ok thanks, now i check both the options and if i get problems or so i’ll let you know. It would appear not.

The sound that just played was a test. Here are the enclosed files from dosflash to be modified to make it wh16ns40 compatible uhd Thanks. I enclose files generated by usb dosflash to be modified to make my rosflash wh16ns40 compatible uhd.

www.makemkv.com

This file was created during the dumping process. When was the drive damaged? I did follow the data mover step…selecting the good 1.

  CANON IR C2880/C3380 PCL5C DRIVER

Is tthe a way through dos with dosflash to get it to show x72? Install the application and open it, in the middle of the window, look for the name of your SATA controller, click the question mark on the right-side, the SATA port is the first 4 four characters in the DeviceIO string.

Xbox Lite-On DG16D2S Extract Key – ivc wiki

Use the table below to find the correct location. I continued reading tutorials and forums but couldnt find anything new to try, then i read about dosflash manual, so i got my correct port and com from ck3 tools and booted to my usb dos, using l-o-eras my sata port i got FF80 a doslfash times but after a power cycle or 2 i got ff72 which means it has been erased, i rebooted to dos atspi tried using dosflash again for writing the new fw dosflasj as usual it gave me ” no atapi devices present ” and showed only my ide’s.

Yes, my password is: Click Ok and a message will report the change was made. This should be obvious, but…. PM me if you have any issues.

BIN file from the Lite-On dump. DosFlash e 1 a0 1 4 D8 0 D8 is the sector erase opcode for the BenQ flash, if you need to erase another drive, lookup jumber value in the datasheet or DosFlash.

  CONEXANT BROADCAST DECODER DRIVER

I had to resort to the DOS version for the same reason TeddyRaspinFeb 6, Launch Firmware Toolbox and open the hacked firmware for the new drive. To verify ddosflash the serial adapter works, make sure the serial-port is enabled in the BIOS, and join loop the Tx and Rx pins together pin 2 and 3.

More information and program DosFlash V2. Thanks to Iriez, Jumba, Redline99 and Tiros for help and support. Download the DVDKey utility.

I’ve attempted both the Windows and DOS versions of the backflash to 3. So, my question is: There ought to be a warning at the beginning of these guides: I have the exact same model as you BH16NS40 and followed all steps.

Sounds like you missed the Data mover step? I have tried every firmware I flash with. Jun 1, Messages:

Start the discussion

Leave a Reply

Your email address will not be published. Required fields are marked *